Yes, I watched it happening. See my messages earlier in this thread. In message #7 I explained how it happened at my site. Basically: gasmeter got changed, but engineer made mistake (wrong capacity meter). Takes it off just after pairing with electricity smart meter, but doesn’t unpair. Installs c ...

Yup, they fucked up (again). In my case it took a lot of persuasion to the contact person of the Liander helpdesk to accept the problem lays in their system. After the first few conversations Liander was still convinced it was a fault in my device, because they could remote read the values. Even ...

Gordon, If you look closely at my last datagram snippet, you'll see two 24.1.0 record id's with a value 3. The first one has no accompanying 24.2.1 gas reading line, the second has. So it's not a case of one gasmeter entry with two gas readings, or a 24.2.1 record id without any relation to a meter ...

@Edgar, you've got mail, but since you have a different meter (output), I guess we don't have the same operator Actually, they're quite equal. I forgot to paste one line; 0-1:24 0-1:24.1.0(003) 0-1:96.1.0(00000000000000000000000000000000) 0-2:24.1.0(003) 0-2:96.1.0 ...

Gordon, I have to think this over a bit. Channel 2: is that 0-1:xx or 0-2:xx? As you say it, it would look at the data at 0-2:xx by your quote. Maybe I understand it wrong. Why wouldn't it pick up the device at 0-2 because it has a device identifier (0-2:24.1.0) and a complete set of data for it? I ...

gordonb3 wrote: ↑Thursday 05 October 2017 22:16 Fabulous! May still look into allowing the channel to be manually overridden but it's nice to see big companies like that be so helpful.

I vote for a possibility to select a channel. But I'll call the grid operator also

Compiling my own Domoticz version is indeed perfectly doable, but it is better to tackle the real problem. When the meter was installed, the fist gas meter appeared to be faulty, so the they took a new one, appearanlty without decoupling the first. I never thought about it until you mentioned there ...

Expand your electrical circuit with a retriggerable monoflop setup. It will recondition the pulse train to a single signal.

Maybe call script with separate parameters (script.php param1 param2 etc) and use $argv[1] $argv[2] and so on?

PM send

Hi Thinkpad, After my july post I haven't done anything with it. I was hoping someone has already picked this up and would chime in but alas! I'm very busy with other things right now, but occasionaly I have some tinker time or am going over some ideas I still have. Basically these are my options ...

Ok, after a short break here are my results: hexcodes for switching device on /off (both 370 and 320) cc2333 for on cc2433 for off for instance: echo -ne '\xcc\x23\x33' | nc -w 3 -n <ipaddress> 5577 hexcodes for color levels (wifi370, 3ch) 56101010aa for each color at level 10(hex) 56ffffffaa for ...

Has anybody succesfully included wifi370 controllers in Domoticz yet? I would like to control them from within domoticz app; use the color picker, dim levels, etc. I'm talking about these: http://g01.a.alicdn.com/kf/HTB13fc5HpXXXXcWaXXXq6xXFXXX5/Wholesale-10Pcs-LED-Wifi-Controller-Wireless-RGB ...

oh, and I read about a humidity sensor.. I don't think mine has one. I have had these pirs since last november I guess. Maybe there's a new version out? If I open the casing I see 2 stickers: on the 'daughterboard': sz40-3011d zw_eu_temp_pir3(ha-015) on the main pcb: sz4f-8901w zw-pic690-temp-pir4 ...

Is there something wrong with settings of this sensor? I did have a problems with this one to. [ battery drain.... ] in what version should the sensor work correct. [ i can test to ] just to chime in.. I have the same issue with battery drain. I have two of them. And batteries last about a month ...

You said you have accept new hardware on when adding the bridge. I don't remember how I added mine but I thought I had to have accept new hardware on and then toggle each light one time on and off to add them to domoticz.

Does this pir sensor have a way to set the re-arm time out? Then it would only reset and trigger again xx seconds after last detection. My zwave motion detectors work that way. During the day I see only a few events; the time someone is in the room and moving is one event so to say.

Me, flevoland

@bbqkees That's interesting. Which starterkit do you have? I thought the LivingColors Remote only worked with the Bloom type of devices. Does it work with the bulbs or led string as well? I bought the HueTap in addition but am not really happy with the way it works. They should have made it battery ...

This was the hard part. You can use Textwrangler to edit your files directly on the rpi. Open TextWrangler (download first), go to File menu, select Open from FTP/SFTP server. Fill in server ip address, loginname (pi) and password (raspberry), and don't forget to select SFTP. (SFTP uses the SSH ...

Hi Edgar! Thanks for the info! My god I have a lot to learn ;) So I just take those scripting lines, paste them in a text editor and save that as a .txt? Is it possible to upload the created file from my Mac to the Rpi without having to take out the SD card? You could use TextWrangler to write the ...