Also as I mentioned, when communicating with these modules indirectly and generate waiting times, the mesh is "obstructed" and for a while the rest of nodes also begin to generate waiting time, although they do communicate directly. The nodes that communicate indirectly are the trigger. Simply, if ...

My mesh is still very small, I only have 5 modules installed and they are all the same (Qubino double relay and Qubino dimmer), so it is easy to make checks by moving the stick and recostuyendo the mesh from different places in the house. If I put the Stick in the center of the house, the signal ...

Same issue here. We has drag this issue from the last three beta updates. I've realized that it only happens with the modules that are not directly connected to the stick. If the signal has to pass through other modules of the network before reaching the stick, the timeouts begin and the entire mesh ...

Thanks, you're right, I'm learning. :) Time ago I watchded information about Mysensors, and even before, I did some artifacts with arduno + esp8266 + 433Mhz to automate some things ... (the video intercom, an IR hub for TV, temperature sensors, etc ...), but DIY solutions require a lot of time to ...

At the end, I returned the two Fibaro FGS-223 because in addition to the double events, with LED bulbs many times did not switch on/off using S1 or S2, when more Watios had the bulb, the problem occurred more often ... with only 20W in normal Led bulbs, the issue happed almost every day, with 8W it ...

At the end, I returned the two Fibaro FGS-223 because in addition to the double events, with LED bulbs many times did not switch on/off using S1 or S2, when more Watios had the bulb, the problem occurred more often ... with only 20W in normal Led bulbs, the issue happed almost every day, with 8W it ...

As far as I understand A is the correct config, don't think your problem has to do with this part of config. Thank you very much, I will keep that configuration then. I do also have double click but it is not a problem in my setup. With what modules you have the double events issue?. You also have ...

Same here.

On the groups of my two Fibaro Double Switch 2 (FGS-223), the controller appears like 1.1.

Maybe this be the cause the issue from the double events with this Fibaro modules ?.

https://www.domoticz.com/wiki/Zwave_network_and_group_info has some god info Thanks, I read it and now I understand a little more. I understand that groups are used for modules to interact with each other, even without having to go through the controller. In the groups of each node, you put the ...

I have excluded and included the modules again (this time using the Domoticz interface instead the button of Z-Stick) and all issues have been solved, except the double events. First I included it again on secure mode, but in addition to double events, sometimes I had timeout of a few seconds. So I ...

I have excluded and included the modules again (this time using the Domoticz interface instead the button of Z-Stick) and the others issues have been solved, the issue with the double events persist.

Well, my first Z-Wave modules have arrived (2 Fibaro FGS-223 v3.2) and I instaled the first... and they have 2 issues. :( When actionate them from Domoticz it causes double events: - for Q1: if I click ON, the events show ON ON and for OFF show OFF OFF. - for Q2: if I click ON, show ON ON ... but if ...

I have installed my first Fibaro 223 module and I have the same issue, when actionate them from Domoticz it causes double events. For Q1: if I click ON the events show ON ON and with OFF shows OFF OFF. B ut for Q2: if I click ON it shows ON ON... but if I click OFF it shows OFF ON, leaving the ...

I just ordered the same modules and USB Stick, as soon as they reach me and I get them to work, I'll tell them if I have that same issue.

Thank you very much Lost.

I have to learn many things about Z-Wave, with these modules that I have buy, I will begin to document me and experiment.

Fibaro devices are great but not so cheap but ok for a smart home budget ;-) No problem if the modules are a little more expensive while they work well. My house is very small, with these 2 modules with double switch that I bought, I cover 1/3 of the lamps in my house. :P Here are the wiki info ...

so.. fibaro will be my new choice (double for lights and single for power outlet/utilities) Thanks, I choose Fibaro also. I read the posts about the issues with FIBARO 223 one more time and appears that the issues had resolve with a uptade of OZW and one restart after pair the module. The first ...

Thank you very much to all. Most issues are range issues and nothing else. My house is small, so I will not have range problems. :) I use Aeotec Gen5, I use both Fibaro and Aeotec (soon CoolCam), no issue at all... I use ZwavePlus, Zigbee, WiFi, LAN and Rfxcom 433Mhz all in my SmartHome Center with ...

Hi, I want to redo the installation of my house to Z-Wave (I have it with RFLink on RP3 and chacon modules 433Mhz, but I need something work better), and since I start with Z-Wave, I would like to have all the modules in Z-Wave Plus. Reading the forum a lot, I have chosen the AeonLabs USB Stick Z ...