Do you use pull-up resistors on these wires? Yep, It's been fine for the past few years. Its just the one pin that's started having this issue. If you remove the connected device, it still happens? If you have a scope, do you see any spikes on the wire? Not tried that yet. It's hard to re-create at ...

SweetPants wrote: ↑Friday 27 July 2018 13:19 Do you use pull-up resistors on these wires?

Yep, It's been fine for the past few years. Its just the one pin that's started having this issue.

Has anyone else experienced a GPIO pin triggering randomly? I've got a few pins connected to my house alarm panel.

In the past 2 weeks one of the pin has triggered by itself and caused an event to fire. This has happened twice. Anyone else experienced this?

I've bought one of these sensors to test, but I've noticed an issue. If the door is opened and shut quickly (5-10secs) I only get the open signal and not the closed. Any one else experienced this?

Cheers
Shyam

b_weijenberg wrote: ↑Tuesday 22 May 2018 11:38 Kerui D026 sensors reported as X10 security sensors is supported by the RFXtrx433E using Ext2 firmware.
See also chapter 2.2.2. in the RFXtrx User Guide.

Right that make sense! Cheers

I've just got one of these. After playing around and updating my RFXtrx433 firmware, I'm able to add 3 new Lighting4 devices (open, closed and tamper). How can I get the battery status? I read on here that if I enable X10, I should see just a security sensor, but I'm not....

anyone? Maybe changing your logic to have time consuming stuff (the snapshot) done at the end (after ringing the bell)? Don't think going with Lua will change anything if snapshot takes time. Or find a way to make snapshot a background operation. Anyway, with so much delay & only 1 snapshot, you'll ...

bump

anyone?

Hello, I've set up an event so that when the door bell is pressed, the chime is sounded, a pushover notification is sent and a snapshot from the camera is emailed. The issue I have is when I added the snapshot send part, it slowed the event right down. It now takes around 20-30seconds, therefore the ...

Hello, I've set up an event so that when the door bell is pressed, the chime is sounded, a pushover notification is sent and a snapshot from the camera is emailed. The issue I have is when I added the snapshot send part, it slowed the event right down. It now takes around 20-30seconds, therefore the ...

I believe then you are going to set up the example script . I've replaced those Hikvision for Dahua ones because I think they are better. The script is not made by me so you'd need to ask the author for help. Thanks! I've got the sample script "working", well it errors, but atleast it connects. How ...

Sorry to bring up a old thread, would you be able to give step by step instructions? I've installed the api, not sure where to go after that :) I believe then you are going to set up the example script . I've replaced those Hikvision for Dahua ones because I think they are better. The script is not ...

for now just wait, I'll try to finish up the code I have and check it into my repo here soon.. if you want to watch for progress you can go here: https://github.com/nayrnet/node-hikvision-api as thats where all the work has to be finished, its not functional at this point. luckily the stream types ...

Well, I think I answered the OP's question? Anyway in my case I have 2 x Velux Integra Windows at a height of 4m in a high vaulted room. I got the KLF-100 a little cheaper from ebay and I only need 1 because I have both windows modulating to control natural cooling under Domoticz control. If I want ...

Hi, this may be worth a look: https://www.domoticz.com/forum/viewtopic.php?t=3360 Thanks! Only issue is that the KLF-100 costs more than I wanted to spend! On top of that, that's one KLF-100 per control... Meaning that if you want to control each window/blinds independently you'll need a lot of KLF ...

StanHD wrote:Hi, this may be worth a look:

https://www.domoticz.com/forum/viewtopic.php?t=3360

Thanks! Only issue is that the KLF-100 costs more than I wanted to spend!

Hello, Has anyone managed to link their Velux electric windows with Domoticz? The problem will basically be an IO-Homecontrol support: This radio protocol is closed and only shared between Somfy & Velux (this is their concept of connected house, only between them!)... Some managed to do some weird ...

Hello,

Has anyone managed to link their Velux electric windows with Domoticz?

Hi,

Did you solve this issue?