Search found 12 matches

by andyk
Tuesday 04 September 2018 22:44
Forum: Switches and Scenes
Topic: Ventilation & humidity switch...can't get it to work.
Replies: 4
Views: 1291

Re: Ventilation & humidity switch...can't get it to work.

Apparantly I was too impatient. After removing the level logic like you said, the fan automatically was switched on after a while. So it works now.
But, the fan is not very strong and it took hours to get from 65% to 60%. So I guess I need a better fan.

Anyway, the blocky script works :D
by andyk
Tuesday 04 September 2018 17:17
Forum: Switches and Scenes
Topic: Ventilation & humidity switch...can't get it to work.
Replies: 4
Views: 1291

Re: Ventilation & humidity switch...can't get it to work.

Hi Arne,

thanks for the info. I removed the level logic, but still nothing happens. Manually, it works. However, when i click 'show current states', it shows temperature and humidity as values. Might that be the problem ? That the values are not equal ?
by andyk
Sunday 02 September 2018 17:15
Forum: Switches and Scenes
Topic: Ventilation & humidity switch...can't get it to work.
Replies: 4
Views: 1291

Ventilation & humidity switch...can't get it to work.

Hi all, EDIT: Forgot to mention, the Humidity sensor is an Aeon Labs Multi 6 sensor. I am running Domoticz on a Pi, version v3.9527 In my bathroom, I have a fan, connected to a Fibaro FGS223 Double Relay. On the dashboard of Domoticz, I can switch the fan on and off. However, I would like automate ...
by andyk
Tuesday 21 August 2018 14:34
Forum: Z-Wave
Topic: Settings Aeotec Multisensor 6
Replies: 3
Views: 1844

Re: Settings Aeotec Multisensor 6

I found the 'timeout' setting. It's parameter 3, which can be found under Setup / Hardware ; click on razbery device (I use a raspberry pi with a Razzbery GPIO module) ; then select one of the Aeotec Multisensors. Parameters are shown below the overview. Or, when in the Nodes overview (As described ...
by andyk
Tuesday 21 August 2018 13:56
Forum: Z-Wave
Topic: Settings Aeotec Multisensor 6
Replies: 3
Views: 1844

Settings Aeotec Multisensor 6

Hi all, I've got several Aeotec Multisensor 6 devices in my network, each serving 1 room (main bathroom, shower, toilet and hall). I want to use them for motion detection icm with a Fibaro dimmer 2 module. I have created several Blockly events; 1 for each room, but it seems that once the Aeotec ...
by andyk
Saturday 18 March 2017 15:09
Forum: Blockly
Topic: Blocky script doesn't work like expected...
Replies: 23
Views: 6404

Re: Blocky script doesn't work like expected...

Sorry to bump this, but does anybody have a clue what may cause the above issue ?

cheers,
Andy
by andyk
Sunday 05 March 2017 16:04
Forum: Blockly
Topic: Blocky script doesn't work like expected...
Replies: 23
Views: 6404

Blocky script doesn't work like expected...

Hi all, I have created a blocky script to activate spots when movement is detected. I use a Fibaro Dimmer 2 for activating the spots; the sensor is a AeonLabs Multisensor 6. My blocky script looks like this: Screen Shot 2017-03-05 at 15.51.22.png When the sensor detects movement, lights are switched ...
by andyk
Sunday 11 December 2016 20:51
Forum: Switches and Scenes
Topic: Getting Fibaro dimmer to work
Replies: 11
Views: 4167

Re: Getting Fibaro dimmer to work

Hi Mischa,

I got so far that the lights switch on when motion is detected. Haven't had time to look at how to switch off lights when no motion is detected in x seconds. If you have tips. I'm all ears :D

Cheers,
Andy
by andyk
Monday 05 December 2016 23:40
Forum: Switches and Scenes
Topic: Getting Fibaro dimmer to work
Replies: 11
Views: 4167

Re: Getting Fibaro dimmer to work

Mischa, Thanks again. I connected another Fibaro Dimmer 2 to the setup and fiddled around with it. It appeared I forgot to set the blockly event to active (DOH!). Now it works. At least, the light switches on when movement is detected. Nice ! Now to figure out how to set the timeout on the dimmer so ...
by andyk
Monday 05 December 2016 22:31
Forum: Switches and Scenes
Topic: Getting Fibaro dimmer to work
Replies: 11
Views: 4167

Re: Getting Fibaro dimmer to work

HI Mischa, Thanks for the example. I am trying to get the setup to work, I have created a blockly script which should just do that, but nothing happens. I see that the Aeotec sensor switches to "On" when movement is detected. However, no lights. The dimmer is shown in the Hardware overview: Screen ...
by andyk
Saturday 03 December 2016 21:21
Forum: Switches and Scenes
Topic: Getting Fibaro dimmer to work
Replies: 11
Views: 4167

Re: Getting Fibaro dimmer to work

Hi, Sorry for my late reply. Thanks for your answer. But, How do I know the multisensor is a security device and how does that affect the way I can use it ? Back to the script example you send. I tried the same using blockly, but didn't get what I wanted. I'll try amd see if the example script of ...
by andyk
Thursday 24 November 2016 23:14
Forum: Switches and Scenes
Topic: Getting Fibaro dimmer to work
Replies: 11
Views: 4167

Getting Fibaro dimmer to work

Hi all, I have a Raspberry Pi 3 with the Razberry Zwave module and running Domoticz 3.5877. After some startup issues this works fine. I have an Aeon Labs Multisensor 6 and a Fibaro Dimmer 2 included, They are both visible in the hardware tab. Now next step would be to connect them, so when the ...