Domoticz

Code: Select all

// Example sketch showing how to control an RGB Led Strip.
// This example will not remember the last rgb color set after power failure.

#include <MySensor.h>
#include <SPI.h>

#include "Adafruit_NeoPixel.h"

#define NUMPIXELS 4   // Number of connected pixels on a single datapin
#define PIN 4         // Digital output pin

#define node 254  //254 for testing purpose
#define CHILD_ID 0  


Adafruit_NeoPixel strip = Adafruit_NeoPixel(NUMPIXELS, PIN, NEO_GRB + NEO_KHZ800);
long RGB_values[3] = {0,0,0};

MySensor gw;

void setup()
{
    gw.begin(incomingMessage, node, true);
    gw.sendSketchInfo("RGB Node", "1.0");
    gw.present(CHILD_ID, S_RGB_LIGHT);
    strip.begin();
    strip.show(); // Update the strip, to start they are all 'off'
}


void loop()
{
    gw.process();
}

void incomingMessage(const MyMessage &message) {
    if (message.type==V_RGB) {
  // starting to process the hex code
        String hexstring = message.getString(); //here goes the hex color code coming from through MySensors (like FF9A00)
        long number = (long) strtol( &hexstring[0], NULL, 16);
        RGB_values[0] = number >> 16;
        RGB_values[1] = number >> 8 & 0xFF;
        RGB_values[2] = number & 0xFF;

        colorWipe(Color(RGB_values[0],RGB_values[1],RGB_values[2]), 60);
     }
     
    if (message.type==V_DIMMER) {
      strip.setBrightness(round((2.55*message.getInt())));
      strip.show();
      }
      
    if (message.type==V_LIGHT) {
       if (message.getInt() == 0) {
        strip.clear();
        strip.show();
       }
    }
  
}
 
void colorWipe(uint32_t c, uint8_t wait) {
  int i;
 
  for (i=0; i < strip.numPixels(); i++) {
      strip.setPixelColor(i, c);
      strip.show();
      delay(wait);
  }
}

    /* Helper functions */

// Create a 15 bit color value from R,G,B
uint32_t Color(byte r, byte g, byte b)
{
  uint32_t c;
  c = r;
  c <<= 8;
  c |= g;
  c <<= 8;
  c |= b;
  return c;
}
    

Code: Select all

void incomingMessage(const MyMessage &message) {
    if (message.type==V_RGB) {
  // starting to process the hex code
        String hexstring = message.getString(); //here goes the hex color code coming from through MySensors (like FF9A00)
        long number = (long) strtol( &hexstring[0], NULL, 16);
        RGB_values[0] = number >> 16;
        RGB_values[1] = number >> 8 & 0xFF;
        RGB_values[2] = number & 0xFF;

        colorWipe(Color(RGB_values[0],RGB_values[1],RGB_values[2]), 60);
     }
     
    if (message.type==V_DIMMER) {
      strip.setBrightness(round((2.55*message.getInt())));
      strip.show();
      }
      
    if (message.type==V_LIGHT) {
       if (message.getInt() == 0) {
        strip.clear();
        strip.show();
       }
    }
  
}

Code: Select all

[spoiler]/*
 PROJECT: MySensors / RGB test for Light & Sensor
 PROGRAMMER: AWI/GizMoCuz
 DATE: september 27, 2015/ last update: October 10, 2015
 FILE: AWI_RGB.ino
 LICENSE: Public domain

 Hardware: Nano and MySensors 1.5
    
 Special:
  uses Fastled library with NeoPixel (great & fast RBG/HSV universal library)       https://github.com/FastLED/FastLED
 
 Remarks:
  Fixed node-id
  Added option to request/apply last light state from gateway
  
 Domoticz typicals - 2015 10 10:
  - Domoticz is using HUE values internally, there might be a slight difference then using direct RGB colors.
*/

#include <MySensor.h>
#include <SPI.h>
#include <FastLED.h>


const int stripPin = 4 ;                  // pin where 2812 LED strip is connected

const int numPixel = 3 ;                  // set to number of pixels

#define NODE_ID 254                       // fixed MySensors node id

#define CHILD_ID 0                  // Child Id's

CRGB leds[numPixel];

char actRGBvalue[] = "000000";               // Current RGB value
uint16_t actRGBbrightness = 0xFF ;         // Controller Brightness 
int actRGBonoff=0;                        // OnOff flag

MySensor gw;

MyMessage lastColorStatusMsg(CHILD_ID,V_VAR1);

void setup() {
  FastLED.addLeds<NEOPIXEL, stripPin >(leds, numPixel); // initialize led strip

  gw.begin(incomingMessage, NODE_ID, false);      // initialize MySensors
  gw.sendSketchInfo("AWI RGB Light", "1.1");
  gw.present(CHILD_ID, S_RGB_LIGHT);        // present to controller

  // Flash the "hello" color sequence: R, G, B, black. 
  colorBars();

  //Request the last stored colors settings
  gw.request(CHILD_ID, V_VAR1);
}

void loop() {
  gw.process();                       // wait for incoming messages
}

void colorBars()
{
  SendColor2AllLEDs( CRGB::Red );   FastLED.show(); delay(500);
  SendColor2AllLEDs( CRGB::Green ); FastLED.show(); delay(500);
  SendColor2AllLEDs( CRGB::Blue );  FastLED.show(); delay(500);
  SendColor2AllLEDs( CRGB::Black ); FastLED.show(); delay(500);
} 

void SendColor2AllLEDs(const CRGB lcolor)
{
  for(int i = 0 ; i < numPixel ; i++) {
    leds[i] = lcolor;
  }
}

void SendLastColorStatus()
{
  String cStatus=actRGBvalue+String("&")+String(actRGBbrightness)+String("&")+String(actRGBonoff);
  gw.send(lastColorStatusMsg.set(cStatus.c_str()));
}

String getValue(String data, char separator, int index)
{
 int found = 0;
  int strIndex[] = {0, -1};
  int maxIndex = data.length()-1;
  for(int i=0; i<=maxIndex && found<=index; i++){
  if(data.charAt(i)==separator || i==maxIndex){
  found++;
  strIndex[0] = strIndex[1]+1;
  strIndex[1] = (i == maxIndex) ? i+1 : i;
  }
 }
  return found>index ? data.substring(strIndex[0], strIndex[1]) : "";
}

void incomingMessage(const MyMessage &message) {
  if (message.type == V_RGB) {            // check for RGB type
    actRGBonoff=1;
    strcpy(actRGBvalue, message.getString());    // get the payload
    SendColor2AllLEDs(strtol(actRGBvalue, NULL, 16));
    SendLastColorStatus();
  }
  else if (message.type == V_DIMMER) {           // if DIMMER type, adjust brightness
    actRGBonoff=1;
    actRGBbrightness = map(message.getLong(), 0, 100, 0, 255);
    FastLED.setBrightness( actRGBbrightness );
    SendLastColorStatus();
  }
  else if (message.type == V_STATUS) {           // if on/off type, toggle brightness
    actRGBonoff = message.getInt();
    FastLED.setBrightness((actRGBonoff == 1)?actRGBbrightness:0);
    SendLastColorStatus();
  }
  else if (message.type==V_VAR1) {            // color status
    String szMessage=message.getString();
    strcpy(actRGBvalue, getValue(szMessage,'&',0).c_str());
    actRGBbrightness=atoi(getValue(szMessage,'&',1).c_str());
    actRGBonoff=atoi(getValue(szMessage,'&',2).c_str());
    SendColor2AllLEDs(strtol(actRGBvalue, NULL, 16));
    FastLED.setBrightness((actRGBonoff == 1)?actRGBbrightness:0);
  }
  FastLED.show();
}

 
[/spoiler]