Hello all,
Who can help me or has an explanation for my problem?
I have been using Domoticz with RFX for months. Everything worked fine. Since this morning I have the following problem.
1 All kaku devices do not respond when controlled by the scripts and dummy switches. With the manual loose kaku switches I can turn the devices on and off.
I tried everything like restarting the NAS, removing the USB plug and putting it back in again. I can't get the case going anymore.
Who knows what to do?
Gr, Peter
RFX has stopped working
Moderator: leecollings
- waaren
- Posts: 6028
- Joined: Tuesday 03 January 2017 14:18
- Target OS: Linux
- Domoticz version: Beta
- Location: Netherlands
- Contact:
Re: RFX has stopped working
Debian buster, bullseye on RPI-4, Intel NUC.
dz Beta, Z-Wave, RFLink, RFXtrx433e, P1, Youless, Hue, Yeelight, Xiaomi, MQTT
==>> dzVents wiki
dz Beta, Z-Wave, RFLink, RFXtrx433e, P1, Youless, Hue, Yeelight, Xiaomi, MQTT
==>> dzVents wiki
-
- Posts: 517
- Joined: Friday 12 July 2013 18:13
- Target OS: -
- Domoticz version:
- Location: Netherlands
- Contact:
Re: RFX has stopped working
Check with RFXmngr if the RFXtrx operates correct. The red LED should blink with a transmit command.
RFXtrx433, RFXtrx433E, RFXtrx433XL, RFX433XL, RFX868XL
-
- Posts: 43
- Joined: Friday 17 July 2020 11:03
- Target OS: NAS (Synology & others)
- Domoticz version:
- Contact:
Re: RFX has stopped working
The same USB output is always used for rfx. As far as I know Rfx manager is only available for Windows. I am using mac and synology (linux). Last night it worked spontaneously again, but this morning the devices stopped responding.
-
- Posts: 43
- Joined: Friday 17 July 2020 11:03
- Target OS: NAS (Synology & others)
- Domoticz version:
- Contact:
Re: RFX has stopped working
Every 5 second the red led on the rfx device goes ON en then the green led blinks af few seconds. Then both goes off. After a few seconds this repeats.
-
- Posts: 517
- Joined: Friday 12 July 2013 18:13
- Target OS: -
- Domoticz version:
- Location: Netherlands
- Contact:
Re: RFX has stopped working
2 possibilities:
1 the RFXtrx restarts due to power drops (check the USB cable and USB power)
2 you transmit every 5 seconds an RF command.
Find a friend with a Windows system and run RFXmngr.
1 the RFXtrx restarts due to power drops (check the USB cable and USB power)
2 you transmit every 5 seconds an RF command.
Find a friend with a Windows system and run RFXmngr.
RFXtrx433, RFXtrx433E, RFXtrx433XL, RFX433XL, RFX868XL
-
- Posts: 43
- Joined: Friday 17 July 2020 11:03
- Target OS: NAS (Synology & others)
- Domoticz version:
- Contact:
Re: RFX has stopped working
I have attached a disk to the USB output of the NAS, it works so that is okay. Go get a new cable tomorrow. Is the length of the USB cable important?
-
- Posts: 43
- Joined: Friday 17 July 2020 11:03
- Target OS: NAS (Synology & others)
- Domoticz version:
- Contact:
Re: RFX has stopped working
Yesterday new cable. Reset Synology NAS. It worked until this morning. Then it stopped again.
Now I get this in the log:
2021-01-21 09:00:29.384 Status: RFXCOM: Async Disabled
Now I get this in the log:
2021-01-21 09:00:29.384 Status: RFXCOM: Async Disabled
Who is online
Users browsing this forum: No registered users and 0 guests