Domoticz

Hi,
I bought the following 3 buttons chinese switch (below).
I have a RFcom working perfectly.
When I push a button of this switch, the RFcom LED is lighting.
That means the frequency is detected by RFcom.
Unfortunately I can not se a new device in the devices list even if the RFlink LED is lighting.

I think I tried every protocols, no success.

Does someone know how to make this switch work with Domoticz?
Anyone can help me ?

Link :
https://fr.aliexpress.com/item/86-Panne ... 14264.html

Picture :

I tested every protocol one by one and I realized that only "undec on" is lighting the RFlink LED.

Does someone know how to make this switch working in this case ?
Is it possible ?

Thanks for your help

You are talking about a RFcom and RFlink, what is it? Using 'undec' suspects you are using a RFXcom right? If that is true, it probably means it's not supported.

SweetPants wrote: Sunday 17 December 2017 12:29 You are talking about a RFcom and RFlink, what is it? Using 'undec' suspects you are using a RFXcom right? If that is true, it probably means it's not supported.

I'm sorry, it's RFXCOM - RFXtrx433 USB 433.92MHz Transceiver (Version: Ext/1020)

Maybe a "stupid question", but you do have the "Accept new Hardware Devices " switched on during these tests?

Jos

jvdz wrote: Sunday 17 December 2017 12:42 Maybe a "stupid question", but you do have the "Accept new Hardware Devices " switched on during these tests?

Jos

Yes, new devices are already accepted.
This is not the cause.

Thanks for your help

Ouate wrote:

jvdz wrote: Sunday 17 December 2017 12:42 Maybe a "stupid question", but you do have the "Accept new Hardware Devices " switched on during these tests?

Jos

Yes, new devices are already accepted.
This is not the cause.

Thanks for your help

I've the single button version which is detected as EV1527 by RFlink.


Verstuurd vanaf mijn SM-G800F met Tapatalk

Lokonli wrote: Sunday 17 December 2017 18:04

Ouate wrote:

jvdz wrote: Sunday 17 December 2017 12:42 Maybe a "stupid question", but you do have the "Accept new Hardware Devices " switched on during these tests?

Jos

Yes, new devices are already accepted.
This is not the cause.

Thanks for your help

I've the single button version which is detected as EV1527 by RFlink.


Verstuurd vanaf mijn SM-G800F met Tapatalk

Hi, can you tell me what is the protocol used by the device?

Ouate wrote:

Lokonli wrote: Sunday 17 December 2017 18:04

Ouate wrote: Yes, new devices are already accepted.
This is not the cause.

Thanks for your help

I've the single button version which is detected as EV1527 by RFlink.


Verstuurd vanaf mijn SM-G800F met Tapatalk

Hi, can you tell me what is the protocol used by the device?

I thought ev1527 is the protocol. Sorry, I don't have more information.

Verstuurd vanaf mijn SM-G800F met Tapatalk

Lokonli wrote: Sunday 17 December 2017 19:34

Ouate wrote:

Lokonli wrote: Sunday 17 December 2017 18:04 I've the single button version which is detected as EV1527 by RFlink.


Verstuurd vanaf mijn SM-G800F met Tapatalk

Hi, can you tell me what is the protocol used by the device?

I thought ev1527 is the protocol. Sorry, I don't have more information.

Verstuurd vanaf mijn SM-G800F met Tapatalk

Hik, the protocol is listed in the devices page. Beside the name of the device.
I will be helpful if you could let me know.

I answer to myself because I found the answer.

This device (The 3 buttons switch) is detected using the protocol "Lightning 4" with a RFXcom
The problem is, when you activacted the protocal "Rubiscon" in the same time, the switch becomes not detected.

Impossible to detect it using the 2 protocols activated in the same time.

I have devices using Rubiscon protocol... I don't know how can I do to use the 2 kinds of devices in the same time.

Does someone has a solution ?