Domoticz

Hello,
is it possible to have compatibility with Aeon Z-Stick and this sensor : BeNext iHome (Door Sensor+Temp+SEC)
http://www.planete-domotique.com/notice ... OORS_M.pdf

I have tested with module Zwave.me and it's fully functional,
but with the Aeon Z-Stick I can't configure him but he's detected :
- Tamper switch : ok (and responsive)
- Temp sensor : ok (but I dont know how to polling)
- Door sensor : no
- SEC sensor : no

Thank's

Erratum contact SEC reacts on the same icon the tamper switch
but no icon for the door sensor ...

Can you send me a PM with your log/config file?
Config/zwcfg_xxxxx.xml
Config/OZW_Log.txt

/Rob

Hi,
as advised I did a post on the Google group OpenZwave
https://groups.google.com/forum/%20#!%2 ... -E-sYJZOaA

and I saw a very similar post on a sensor BeNext
https://groups.google.com/forum/%20#!%2 ... zMPbQQv0-4

wait and see...

another manufacturer's product as the same problem ...
http://code.google.com/p/open-zwave/iss ... rt=&id=267

I have already said, but: there is a new door sensor in BeNext (with temperature) and id (new: type = 0004, id = 0101) is different from the old door sensor (old: type = 0004, id = 0100) it is poorly recognized as "Digital Home Systems Unknown: type = 0004, id = 0101" Digital Home Systems has an id (008a) of the same manufacturer BeNext (008a) in the "manufacturer_specific file. xml "

more on this site this new sensor is referenced with id 100 may be that the problem comes from here?
http://www.pepper1.net/zwavedb/device/149

Hi,

I have the same problem.

I saw, the open-zwave code are updated for the new version.

It's possible to update the manufacturer_specific.xml file and all benext files ?

Best regards

Yes, but they will be overwritten when a new release of openzwave is made.
At the moment i added a custom philio 3-1 sensor in it...
if this is working well (derrik... is it working well? i will post the modifications on the openwave forum/issue.

If you make changes for a new device, and it is working correctly, please do the same...

There are many many zwave devices, and it's impossible to have them all supported helping openzwave with this is the way to go

Hi,

The new openzwave version 1.0.758 http://www.openzwave.com/snapshots/ is updated with the new BeNext sensor

Can you update domoticz with this version ?

Very thanks

Best regards

This version is already in domoticz since 19 Feb.

You could try to backup your zwave configuration file, and delete the current one.

stop domoticz
cp Config/zwcfg_xxxxxx.xml Config/zwcfg_xxxxxx.bak
rm Config/zwcfg_xxxxxxx.xml
start domoticz

Hi,

The manufacturer_specific.xml isn't the version 1.0.758 in my raspberry. They are more diffence between the local file and the fine in version 1.0.758

By exemple this line doesn't existe in domoticz version V1.1575 (in benext section)!!!

<Product type="0003" id="0101" name="DHS-ZW-SNMT-01 Multi Sensor" config="BeNext/Molite.xml"/>

Best regards

should be solved now with the latest beta

Now it's OK

Thanks

great ! they aren't detected as "BeNext" but works perfectly, thank you!

I ordered a benext door sensor. Is this the same? It's recognised (all the devices) and listed as a benext but it's not working (gets a timeout after a few mins and never works again).
There is another thread: viewtopic.php?f=17&t=7376&p=63009#p63009
H