Domoticz

Hello!

I am new to domoticz with an raspberry pi 3 and a RFXTRX433E

On aliexpress i bought some KERUI D026 door sensors
http://www.aliexpress.com/item/32590916 ... 16896.html


But they are not recognized by RFXTRX433E and Domoticz. Is there ant way to make them work?

Check with RFXmngr on a Windows system and Lighting4 enabled

Thank you for your reply! I checked today with RFXmngr with Lighting 4 enabled.

CLOSE

------------------------------------------------
------------------------------------------------
Packettype = Lighting4
subtype = PT2262
Sequence nbr = 154
Code = 424087 decimal:4341895
S1- S24 = 0100 0010 0100 0000 1000 0111
Pulse = 317 usec
Signal level = 8 -56dBm



OPEN
------------------------------------------------
------------------------------------------------
Packettype = Lighting4
subtype = PT2262
Sequence nbr = 155
Code = 42408E decimal:4341902
S1- S24 = 0100 0010 0100 0000 1000 1110
Pulse = 317 usec
Signal level = 8 -56dBm
------------------------------------------------
------------------------------------------------

PANIC

------------------------------------------------
------------------------------------------------
Packettype = Lighting4
subtype = PT2262
Sequence nbr = 234
Code = 42408B decimal:4341899
S1- S24 = 0100 0010 0100 0000 1000 1011
Pulse = 315 usec
Signal level = 8 -56dBm
------------------------------------------------
------------------------------------------------

Is there a way to add thus sensor ?


Verzonden vanaf mijn iPhone met Tapatalk

I have also some Kerui D026 sensors and they working with Domoticz. I'm running SW version 1009, you can download it from the RFXcom website, you can only reload the firmware/SW version via the windows program (not via Domoticz). You have to selected lighting4 (modus instellen)...

robertje221 wrote:Is there a way to add thus sensor ?

Verzonden vanaf mijn iPhone met Tapatalk

Dear friend,

I bought a Kerui D026 sensor and I made it work with my RFLINK gateway as easy as 1-2-3. The only problem is that the ON means closed and OFF means opened, and I want to swap it but cannot find the solution.. But the sensor is working flawless!

Thanks for your reply. I know that these sensors are supported with the RFlink. But I have a RFXTRX433E / RFXCOM and i wonder if it is possible to make them work with that unit.


Verzonden vanaf mijn iPhone met Tapatalk

TacticalLeader wrote:

robertje221 wrote:Is there a way to add thus sensor ?

Verzonden vanaf mijn iPhone met Tapatalk

Dear friend,

I bought a Kerui D026 sensor and I made it work with my RFLINK gateway as easy as 1-2-3. The only problem is that the ON means closed and OFF means opened, and I want to swap it but cannot find the solution.. But the sensor is working flawless!

Make a Dummy
Make Blockley
When open cloe the the dummy
When close open the dummy..

Derik wrote:

TacticalLeader wrote:

robertje221 wrote:Is there a way to add thus sensor ?

Verzonden vanaf mijn iPhone met Tapatalk

Dear friend,

I bought a Kerui D026 sensor and I made it work with my RFLINK gateway as easy as 1-2-3. The only problem is that the ON means closed and OFF means opened, and I want to swap it but cannot find the solution.. But the sensor is working flawless!

Make a Dummy
Make Blockley
When open cloe the the dummy
When close open the dummy..

I will have 17 dummys for reversing and 17*2 switches for nothing. It's not too elegant.

ok ....
Only it is a solution... [ did not now you have 17 contact.. ]
And Domoticz can run with the dummy no problem..
Think i do have 100+ dummy timer active etc etc ..

Derik wrote:ok ....
Only it is a solution... [ did not now you have 17 contact.. ]
And Domoticz can run with the dummy no problem..
Think i do have 100+ dummy timer active etc etc ..

By the way, the solution is working and do the reversing. Maybe, if there will be a solution to hide selected switches or other devices Now the switches menu is crowded, like a christmas market.

On request a beta version Ext2 (for the RFXtrx433E) is available. This firmware reports Kerui sensors as one security sensor.

Should this work with RFXcom433E (ver1011)? And does this one have ON and OFF switch? So I can see of the door is closed or opened?
It's not really Kerui, but does have the same D026 code.... Chinese sellers aren't always sincere in their ads.

https://www.aliexpress.com/item/High-gr ... 2167&tpp=1

Or should I go for a real Kerui D026?


UPDATE 23/12: Device works great... Gonna buy some more:)

Updated the firmware of my RFXcom433E to ver1012.
The Kerui D026 is now a proper security sensor with three states (normal, alarm and alarm+tamper).

Unfortunately only 3 of 5 identical Kerui D026 sensors are successfully added to Domoticz.
The other two won't even show up in the RFXcom manager log.
They do seem to work; the led blinks and signal sending is audible.
Any suggestions?

Please contact support rfxcom.com as this is not a Domoticz problem!

No need to shout. Thank you for your reply, I will contact support at rfxcom.

The two sensors are indeed working. I have collected undecoded ARC for both sensors and contacted RFXcom with the information.

Hi Boxel, also I have some Kerui, 4 units are not responding in RFXcom, how did you manage to get them working?

Hi,

Problem with the Kerui sensors is: the look the same, but they have different protocols.
Also if you have Rubicson enabled, the most sensors won't respond.

They are working on a fix (new firmware), but it's not perfect yet.

At least, I've got mine working with a lot of support. (thx Bert)