Domoticz

If you can use Ext2 firmware enable Lighting4 and X10 and the Kerui sensor will be decoded by the RFXtrx433E as a X10 security sensor.

Hi, my sensor came in today. Tried to learn it AUTOMATIC, but no succes. (clone of a Kerui D026, but also a KR-D026)
Sensor lights when door is closed, opens or the switch on the back goes to 'unmounted' (protection if someone removes the switch)

In RFXmngr with Undec ON and only Lighting 4 ON, I get these messages:

How should I install this sensor? I already installed version 1012 on my RFXcom433E.

Here another pic of the manual of the door-sensor.

Already got it to work in Domoticz. Was maybe a problem with too may protocols on. Turned almost every protocol off and now it works...

Now finding out what the statusses are for programming the switch in LUA

Hi,

Problem with the Kerui sensors is: the look the same, but they have different protocols.
Also if you have Rubicson enabled, the most sensors won't respond.

They are working on a fix (new firmware), but it's not perfect yet.

At least, I've got mine working with a lot of support. (thx Bert)

Hi Melissen,

Do they send andON signal only, or ON & OFF?
I am looking now for new sensors, but i want them to report ON/OFF

ArieKanarie wrote:Hi Melissen,

Do they send andON signal only, or ON & OFF?
I am looking now for new sensors, but i want them to report ON/OFF

+1 for this question indeed.

Hi, I can confirm, they send 3 different signals : On, off, and tamper (when dismounted from the door/wall)

Link : https://fr.aliexpress.com/item/High-gra ... 21054.html

"Désolé, cet article n'est plus disponible !"

Oh I just see that .... I bought this set 2 weeks ago and received them this week ... from this listing.

Sorry ... But I can confirm they are the same as pictured by Melissen (same insides)

psst...
https://nl.aliexpress.com/item/5pcs-lot ... 54563.html

Just ordered these.. now hope they send different open close tamper signal that rflink van decode. They don't have the brand name on it..
@ariekanarie: did You manage to get the other two up and running? You reported that two sensors could not be paired with your system.

Yes, finally I succeeded, with help. (disabeling all other protocols was the trick)
But that was not with the sensors from my last post, that was with other doorsensors, which I wanna replace because they only send ON signal.
The ones from my last post should be the same as the ones from Bernardstef.

Received them very fast. Using IT with rflink but receive continuous other id and unit. Not useable this way. Maybe i should contact rflink team...

That is a shame

jackderuiter wrote:Received them very fast. Using IT with rflink but receive continuous other id and unit. Not useable this way. Maybe i should contact rflink team...

Sooo .. they are not working with rflink ?

Not yet. Had a reply from rflink guys but it is not yet working. Should use learning mode but debug log shows IT is not showing correct responses.

Any luck yet?
Still looking for some nice door/window sensors with on/off signal..

ArieKanarie wrote:psst...
https://nl.aliexpress.com/item/5pcs-lot ... 54563.html

I also also ordered these.

They worked out of the box with RFLink R46 firmware for me:

Unit 0 off for close
Unit 1 on for open
Unit 2 on for tamper alarm.

Commands seem to be sent 3 times each.

Cheers

Scott

I did not get it up and running with these or at least similar looking sensors. Still gave me different main and unit ids. Rflink progamming command feature did not work for me.

Verstuurd vanaf mijn XT1562 met Tapatalk