Page 2 of 2
Re: Kerui D026
Posted: Wednesday 28 June 2017 22:27
by EdddieN
Hi,
I'm testing this one too, I have it recognised with RFXcom as Lighting4 sensor. However Domoticz shows them always as ON, but I can see on the logs that both, open and closed are received as:
I have RFXtrx433E version with fw Type2/1017
Are you able to get it working as open closed?
Re: Kerui D026
Posted: Friday 11 August 2017 10:20
by denman091
Hi Guys,
I'm a new domoticz user. I have a RFXCom433e with Ext2/1020 firmware.
I want a door sensor witch i can add as a single security device. Open and Closed. I read that de Kerui D026 is supported in version 1012 by rfxcom but witch one i should by?
https://www.aliexpress.com/item/433MHz- ... 40451.html?
Or:
https://www.aliexpress.com/item/D026-Wi ... 30002.html?
Or are these 2 identical?
Re: Kerui D026
Posted: Thursday 31 August 2017 8:18
by iLLiac4
I was testing D026 sensor with RFXTfx433E (1020) and if i enable only lightning4 protocol it receives open, close and temper signal but no battery status.
If i enable also x10 and lightning 4 protocol all three (open, close, temper) are sended as one signal, which is kind of not usefull.
Code: Select all
31. 08. 2017 08:16:34
Packettype = Security1
subtype = X10 security
Sequence nbr = 1
id1-3 = 110D00 decimal:1117440
status = Alarm + Tamper
battery level = OK
Signal level = 8 -56dBm
Is this a normal behaviour?
Re: Kerui D026
Posted: Thursday 31 August 2017 8:23
by b_weijenberg
Is the tamper switch closed?
What is received with X10 disabled?
Re: Kerui D026
Posted: Thursday 31 August 2017 9:01
by iLLiac4
Hmm. Is seems that it is domotics bug. As it lists as only one status. Will investigate further.
Status in rfx is:
------------------------------------------------
31. 08. 2017 09:00:57
------------------------------------------------
31. 08. 2017 09:00:58
Packettype = Security1
subtype = X10 security
Sequence nbr = 0
id1-3 = 110D00 decimal:1117440
status = Normal
battery level = OK
Signal level = 8 -56dBm
------------------------------------------------
31. 08. 2017 09:01:01
------------------------------------------------
31. 08. 2017 09:01:01
Packettype = Security1
subtype = X10 security
Sequence nbr = 1
id1-3 = 110D00 decimal:1117440
status = Alarm
battery level = OK
Signal level = 8 -56dBm
------------------------------------------------
31. 08. 2017 09:01:03
------------------------------------------------
31. 08. 2017 09:01:03
Packettype = Security1
subtype = X10 security
Sequence nbr = 2
id1-3 = 110D00 decimal:1117440
status = Alarm + Tamper
battery level = OK
Signal level = 8 -56dBm
Re: Kerui D026
Posted: Tuesday 22 May 2018 9:32
by Shyam
I've just got one of these. After playing around and updating my RFXtrx433 firmware, I'm able to add 3 new Lighting4 devices (open, closed and tamper). How can I get the battery status? I read on here that if I enable X10, I should see just a security sensor, but I'm not....
Re: Kerui D026
Posted: Tuesday 22 May 2018 11:38
by b_weijenberg
Kerui D026 sensors reported as X10 security sensors is supported by the RFXtrx433E using Ext2 firmware.
See also chapter 2.2.2. in the RFXtrx User Guide.
Re: Kerui D026
Posted: Tuesday 22 May 2018 12:08
by Shyam
b_weijenberg wrote: ↑Tuesday 22 May 2018 11:38
Kerui D026 sensors reported as X10 security sensors is supported by the RFXtrx433E using Ext2 firmware.
See also chapter 2.2.2. in the RFXtrx User Guide.
Right that make sense! Cheers
Re: Kerui D026
Posted: Friday 06 July 2018 10:47
by Shyam
I've bought one of these sensors to test, but I've noticed an issue. If the door is opened and shut quickly (5-10secs) I only get the open signal and not the closed. Any one else experienced this?
Cheers
Shyam
Re: Kerui D026
Posted: Sunday 09 September 2018 21:09
by harolds
The close signal is not received of processed correctly most of the time.