Domoticz

Purejet wrote:Trying to install Homebridge again. Service is running now. But when i open an Homekit app i don't see my bridge to connect with...

phobosman wrote:Should contact sensors also work with mqtt now? I have mqtt up an running perfectly with switches and motion sensors but my two contact sensors does not send mqtt updates... is this a known issue?

TheRamon wrote:

phobosman wrote:Should contact sensors also work with mqtt now? I have mqtt up an running perfectly with switches and motion sensors but my two contact sensors does not send mqtt updates... is this a known issue?

I'm not sure, never tested contact sensors as I myself don't have one.
Could you send device output JSON? (see first post)
I'll check to see if they're implemented.

phobosman wrote:Ok here's my JSON output, thanks!

Spoiler: show

Code: Select all

{
   "ActTime" : 1481660671,
   "ServerTime" : "2016-12-13 21:24:31",
   "Sunrise" : "08:39",
   "Sunset" : "14:45",
   "result" : [
      {
         "AddjMulti" : 1.0,
         "AddjMulti2" : 1.0,
         "AddjValue" : 0.0,
         "AddjValue2" : 0.0,
         "BatteryLevel" : 100,
         "CustomImage" : 0,
         "Data" : "Closed",
         "Description" : "",
         "Favorite" : 1,
         "HardwareID" : 5,
         "HardwareName" : "Aeon ",
         "HardwareType" : "OpenZWave USB",
         "HardwareTypeVal" : 21,
         "HaveDimmer" : true,
         "HaveGroupCmd" : true,
         "HaveTimeout" : false,
         "ID" : "00001000",
         "Image" : "Light",
         "IsSubDevice" : false,
         "LastUpdate" : "2016-12-07 16:36:46",
         "Level" : 0,
         "LevelInt" : 0,
         "MaxDimLevel" : 100,
         "Name" : "Altandörren",
         "Notifications" : "false",
         "PlanID" : "0",
         "PlanIDs" : [ 0 ],
         "Protected" : false,
         "ShowNotifications" : true,
         "SignalLevel" : "-",
         "Status" : "Closed",
         "StrParam1" : "",
         "StrParam2" : "",
         "SubType" : "Switch",
         "SwitchType" : "Contact",
         "SwitchTypeVal" : 2,
         "Timers" : "false",
         "Type" : "Light/Switch",
         "TypeImg" : "contact",
         "Unit" : 1,
         "Used" : 1,
         "UsedByCamera" : false,
         "XOffset" : "0",
         "YOffset" : "0",
         "idx" : "302"
      }
   ],
   "status" : "OK",
   "title" : "Devices"
}

harrykausl wrote:Hello,
how can I see, if there's a new version of the plugin available and how can I install it.Thanks!

@fennec62 : I t seems that I also have problems with my blinds in IOS 10.2. What is mqtt-integration-RFXMeter
, is it a special mqtt?

sudo service homebridge stop
sudo git clone -b mqtt-integration-RFXMeter https://github.com/PatchworkBoy/homebridge-edomoticz.git
 cd homebridge-edomoticz
sudo npm install
sudo service homebridge start

Jem101 wrote:Something that I have only just noticed but it may have been happening for a while now, is that my electricity consumption meter is no longer reporting properly.

It's an Owl device which is recognised by Domoticz as a CM113 Electrisave device, Domoticz shows the correct figures, I realise that this is not supported by the built-in 'home' app in iOS10 but it always used to work ok in Eve and now doesn't.

Spoiler: show

Code: Select all

{
    "ActTime": ​1482257252,
    "ServerTime": "2016-12-20 18:07:32",
    "Sunrise": "08:08",
    "Sunset": "15:53",
    "result": 
[
{
    "AddjMulti": ​1.0,
    "AddjMulti2": ​1.0,
    "AddjValue": ​0.0,
    "AddjValue2": ​0.0,
    "BatteryLevel": ​100,
    "CounterToday": "13.339 kWh",
    "CustomImage": ​0,
    "Data": "6208.283 kWh",
    "Description": "",
    "Favorite": ​0,
    "HardwareID": ​2,
    "HardwareName": "RFXCOM",
    "HardwareType": "RFXCOM - RFXtrx433 USB 433.92MHz Transceiver",
    "HardwareTypeVal": ​1,
    "HaveTimeout": false,
    "ID": "00006492",
    "LastUpdate": "2016-12-20 18:06:46",
    "Name": "Owl",
    "Notifications": "false",
    "Options": "",
    "PlanID": "2",
    "PlanIDs": 
            [
                ​2
            ],
            "Protected": false,
            "ShowNotifications": true,
            "SignalLevel": ​7,
            "SubType": "kWh",
            "SwitchTypeVal": ​0,
            "Timers": "false",
            "Type": "General",
            "TypeImg": "current",
            "Unit": ​1,
            "Usage": "671.0 Watt",
            "Used": ​1,
            "XOffset": "80",
            "YOffset": "481",
            "idx": "9"
        }
    ],
    "status": "OK",
    "title": "Devices"
}

TheRamon wrote:I can confirm Authorization broke in the last commit. I was a bit too enthusiastic with the refactoring and all. Have just fixed this issue on git / master. My apologies.

PS. G3rard: good find! Let me investigate. Looks like this is a Domoticz thing.

Spoiler: show

Code: Select all

{
    "bridge": {
        "name": "Homebridge",
        "username": "CC:21:3E:E4:DE:33",
        "port": 51826,
        "pin": "031-45-154"
    },
    "description": "Configuration file for (e)xtended Domoticz platform.",
    "platforms": [
        {
            "platform": "eDomoticz",
            "name": "eDomoticz",
            "server": "127.0.0.1",
            "port": "8080",
            "ssl": 0,
            "roomid": 2,
            "mqtt": true
        }
    ],
    "accessories": []
}

harrykausl wrote:Hello,
how can I see, if there's a new version of the plugin available and how can I install it.Thanks!

G3rard wrote: Did you already had a closer look at the dimlevel using MQTT (regarding the 1% off)?

TheRamon wrote:@phobosman:
I have just pushed a new version to git and npm. This version has contact switches implemented. (MQTT)
My apologies for only getting back to you now. I have been very busy lately!