HOME COMFORT modules (or SMART HOME / IDK) ECR-100

[sebitop]

Hi guys

does someone managed to have the ECR-100 module working with domoticz ?

here is the link

http://www.home-confort.net/fr/content/ ... -chauffage

I tried different signals but i don't know if i'm doing it well.

thank you in advance for your help

[ThinkPad]

Looks exactly the same as: http://www.klikaanklikuit.nl/shop/nl/in ... -acm-1000/
Use type 'AC', use random code and when unit is in paring mode, click 'Test' button in Domoticz.



Let me know if it works

[sebitop]

Thanks

it looks but it's not exactly the same, mine as a green led and seems to refuse to work with AC

I will try again this evening and keep you posted, could be usefull to know.

[Stuntteam]

Looks exactly the same as: http://www.klikaanklikuit.nl/shop/nl/in ... -acm-1000/
Use type 'AC', use random code and when unit is in paring mode, click 'Test' button in Domoticz.

Let me know if it works

I doubt it is the same.
The RFLink Gateway supports the Home Confort Smart Home products (among others the TEL-010 remote control) and the protocol is totally different.

[sebitop]

i tried by it dosen't work ...

[sebitop]

I've been in contact with the RFXCOM team to implement this protocol on the RFXCOM module.

I just tested it with RFXMGR and it works perfectly i'm able to control these new modules

so now just nee to be implemented in Domoticz.

I posted a modification request in the tracker.

et me know if you need any help to test it.

cheers

sebastien

[sebitop]

more info on HOME COMFORT modules : http://www.home-confort.net

they are exactly the same than chacon but cheaper (got one for 10€)

[deennoo]

Need this to !

[sebitop]

here the request in the tracker

http://www.domoticz.com/forum/tracker.php?p=2&t=615

the protocol is already available in the last RFXCOM firmware but need to be avilable on Domoticz;

[slybreiz]

Hello

I have several ecr-100 Module

I can not operate with a domotickz and rxfcom433E Version 248.

help thank you

[b_weijenberg]

Did you try with RFXmngr?

I suppose HomeConfort is not yet implemented in Domoticz, see http://www.domoticz.com/forum/tracker.php?p=2&t=615

[slybreiz]

Hello

I just tested RFXmngr.

The selection I HC tab.
and selection of telecommandeTEL-010 (the remote control supplied with the ECR-100 module is the TEL-010 model)

I try a aperage but nothing happens.

I was therefore unable to operate the ECR-module 100 ave key RFXcom433E ....

[b_weijenberg]

Use an RFXtrx433E with firmware version 248.
Connect RFXmngr and enable only the HomeConfort protocol,
Transmit a command using the TEL-010 remote.
Check the codes received and transmit a command with RFXmngr using the same codes as received from the TEL-010.

Capture.JPG (37.59 KiB) Viewed 6508 times

[slybreiz]

It's ok

================================================
Home Confort command
================================================
Packettype = Home Confort
subtype = TEL-010
Sequence nbr = 6
ID = 1010C decimal:65804
House Code = A
Unit Code = 1
Command = On
Signal level = 0 -120dBi
------------------------------------------------
Packettype = Receiver/Transmitter Message
subtype = Transmitter Response
Sequence nbr = 6
response = ACK, data correct transmitted
================================================
Home Confort command
================================================
Packettype = Home Confort
subtype = TEL-010
Sequence nbr = 7
ID = 1010C decimal:65804
House Code = A
Unit Code = 1
Command = Off
Signal level = 0 -120dBi
------------------------------------------------
Packettype = Receiver/Transmitter Message
subtype = Transmitter Response
Sequence nbr = 7
response = ACK, data correct transmitted

Merci Thank's :p

[forumfab]

Ok, HOME COMFORT modules are know seen under RFXmgr, but not by DOMOTICZ

Best regards

[gizmocuz]

Implemented in #3524, hope it works well

[slybreiz]

Nice job it's ok For me .

[gizmocuz]

Great! thanks for the feedback

[sebitop]

bakc from business trip I will try it soon and post a feedback

thank you gizmo !!

S.

[forumfab]

Implemented in #3524, hope it works well

Hi gizmocuz,

Imposible to check "home confort" box in hardware set mode !

The system refuse this choice !

it's the same think with usb rfxcom 433 and usb rfxcom 433 E

Do you have an idea ?

Bests regards