Multi value custom sensor

[TDer]

This is exactly what I was looking for and too bad there isn't such a multi value custom sensor available yet
Testing here with SDS011 and ESPeasy on a Wemos D1.
I was hoping to get some graphs during newyear, but now I only can graph the PM2.5.

[thorian]

Untill it arrvies I'm using the rules in ESP Easy for ESP8266 to send both PM 2,5 and PM10 to Domoticz:

Code: Select all

 SendToHTTP 192.168.1.45,8888,/json.htm?type=command&param=udevice&idx=201&nvalue=0&svalue=[SDS011#PM25] 
 SendToHTTP 192.168.1.45,8888,/json.htm?type=command&param=udevice&idx=202&nvalue=0&svalue=[SDS011#PM10] 
 

Where 201 and 202 are Custom sensors.

[MaikelK]

How does this work?

[McMelloW]

+1

Love to have Custom Sensor accepting multi values. ie number / text etc

Any body working on this already ?

[Spitfire]

Another +1,

Very useful for bandwith coverage, Mi flora flower sensors etc...

[PieterS]

+1

Should be nice feature!

[miroslavpetrov]

Untill it arrvies I'm using the rules in ESP Easy for ESP8266 to send both PM 2,5 and PM10 to Domoticz:

Code: Select all

 SendToHTTP 192.168.1.45,8888,/json.htm?type=command&param=udevice&idx=201&nvalue=0&svalue=[SDS011#PM25] 
 SendToHTTP 192.168.1.45,8888,/json.htm?type=command&param=udevice&idx=202&nvalue=0&svalue=[SDS011#PM10] 
 

Where 201 and 202 are Custom sensors.

Can you please share the entire Rule? I am not sure how to make the execution of the request every xx seconds.

[Patrykwaw]

I use exactly the same method to send values from PMS5003

Code: Select all

On System#Boot do
   timerSet,1,10
  endon

On Rules#Timer=1 do 
  GPIO,12,0
  timerSet,2,60
endon

On Rules#Timer=2 do
    SendToHTTP xxx.xxx.xxx.xxx,80,/json.htm?type=command&param=udevice&idx=130&nvalue=0&svalue=[dust#PM10]
    SendToHTTP xxx.xxx.xxx.xxx,80,/json.htm?type=command&param=udevice&idx=133&nvalue=0&svalue=[dust#PM1]
    SendToHTTP xxx.xxx.xxx.xxx,80,/json.htm?type=command&param=udevice&idx=132&nvalue=0&svalue=[dust#PM25]
 GPIO,12,1
  timerSet,1,1800
endon

After system boot wait 10 seconds for wifi connections etc.

Code: Select all

On System#Boot do
   timerSet,1,10
  endon

Switch on power for dust sensor and wait 60 seconds for proper data reading

Code: Select all

On Rules#Timer=1 do 
  GPIO,12,0
  timerSet,2,60
endon

Send values to domoticz and switch off power

Code: Select all

On Rules#Timer=2 do
    SendToHTTP xxx.xxx.xxx.xxx,80,/json.htm?type=command&param=udevice&idx=130&nvalue=0&svalue=[dust#PM10]
    SendToHTTP xxx.xxx.xxx.xxx,80,/json.htm?type=command&param=udevice&idx=133&nvalue=0&svalue=[dust#PM1]
    SendToHTTP xxx.xxx.xxx.xxx,80,/json.htm?type=command&param=udevice&idx=132&nvalue=0&svalue=[dust#PM25]
 GPIO,12,1

Set Timer one for 1800 sec

Code: Select all

  timerSet,1,1800
endon

[PatrykMilewski]

+1

I need this for custom virtual temperature measurements

[angelus1753]

+1

(new to this, and surprised it isn't there already)

[Qcvictor]

+1 because I'm in metric and my wife in imperial, will be great to display temperature Celsius/Fahrenheit in the custom sensor

[ronilee]

Is there something new here?

My problem:

I have a new UV Sensor VEML6070.
I use EasyESP to send the data to domoticz.

My problem:

This sensor has three values, UV-Raw / UV-Risk / UV-Power

I have created a virtual custom sensor, but the only shown me the first value UV-Raw.

Do you have an idea how i can display the 2 and 3 value?

Thanks a lot