Why is RFLink writing in the Log

[DutchHans]

I am on a raspberry, latest Beta and I am experiencing strange behaviour from RF Link .

Th Log is written full with RFLink devices that aren't there; they are connected to my RFXCom-RFXTRX.
Where is this coming from?? RFLink receives them first and writes it in the log (but it shouldn't) and than Rfxcom...

Why?


2017-10-14 14:11:30.192 RFLink: 20;24;Oregon CM119;ID=006C;WATT=0293;KWATT=0018ddd8;
2017-10-14 14:11:30.392 (RfxCom-1) Energy (Total Energy Consumption)
2017-10-14 14:11:31.183 RFLink: 20;25;Cresta;ID=3E01;TEMP=00bf;HUM=62;BAT=OK;
2017-10-14 14:11:31.187 (RfxCom-1) Temp + Humidity (Temperature Bedroom)
2017-10-14 14:11:33.959 OpenZWave: Received timeout notification from HomeID: 3530462996, NodeID: 32 (0x20)
2017-10-14 14:11:34.080 RFLink: 20;26;Alecto V4;ID=550a;TEMP=00ca;HUM=20;
2017-10-14 14:11:35.545 (Z-wave Controller ) Usage (Dishwasher Usage)
2017-10-14 14:11:35.552 (Z-wave Controller ) General/kWh (kWh Meter Dishwasher)
2017-10-14 14:11:37.045 (Z-wave Controller ) Usage (Dishwasher Usage)
2017-10-14 14:11:37.052 (Z-wave Controller ) General/kWh (kWh Meter Dishwasher)
2017-10-14 14:11:38.545 (Z-wave Controller ) Usage (Dishwasher Usage)
2017-10-14 14:11:38.552 (Z-wave Controller ) General/kWh (kWh Meter Dishwasher)
2017-10-14 14:11:42.194 RFLink: 20;27;Oregon CM119;ID=006C;WATT=0273;KWATT=0018ddda;
2017-10-14 14:11:42.270 (RfxCom-1) Energy (Total Energy Consumption)
2017-10-14 14:11:46.344 (RfxCom-1) Temp + Humidity (Temperature Office)
2017-10-14 14:11:47.548 (Z-wave Controller ) Usage (Dishwasher Usage)
2017-10-14 14:11:47.558 (Z-wave Controller ) General/kWh (kWh Meter Dishwasher)
2017-10-14 14:11:48.195 (RfxCom-1) Temp + Humidity (Fridge Temp)
2017-10-14 14:11:49.042 (Z-wave Controller ) Usage (Dishwasher Usage)
2017-10-14 14:11:49.046 (Z-wave Controller ) General/kWh (kWh Meter Dishwasher)
2017-10-14 14:11:50.542 (Z-wave Controller ) Usage (Dishwasher Usage)
2017-10-14 14:11:50.546 (Z-wave Controller ) General/kWh (kWh Meter Dishwasher)
2017-10-14 14:11:52.045 (Z-wave Controller ) Usage (Dishwasher Usage)
2017-10-14 14:11:52.053 (Z-wave Controller ) General/kWh (kWh Meter Dishwasher)
2017-10-14 14:11:54.194 RFLink: 20;28;Oregon CM119;ID=006C;WATT=0263;KWATT=0018dddc;
2017-10-14 14:11:54.275 (RfxCom-1) Energy (Total Energy Consumption)
2017-10-14 14:11:55.279 (RfxCom-1) Temp + Humidity (Temperature Livingroom)
2017-10-14 14:11:57.086 RFLink: 20;29;Alecto V4;ID=59c8;TEMP=00e5;
2017-10-14 14:11:58.045 (Z-wave Controller ) Usage (Dishwasher Usage)
2017-10-14 14:11:58.053 (Z-wave Controller ) General/kWh (kWh Meter Dishwasher)
2017-10-14 14:12:03.091 RFLink: 20;2A;Cresta;ID=3501;TEMP=00a7;HUM=80;BAT=OK;
2017-10-14 14:12:03.094 (RfxCom-1) Temp + Humidity (Temperature Outside)
2017-10-14 14:12:08.554 (Z-wave Controller ) Usage (Dishwasher Usage)
2017-10-14 14:12:08.573 (Z-wave Controller ) General/kWh (kWh Meter Dishwasher)

[Plantje]

Did you ever figure this one out? I am seeing the same issue.

[DutchHans]

No..the issue still exists...
Merry Christmas

[SweetPants]

I think, although only one transceiver is assigned to the hardware device, the other is receiving the messages too and writes it to the log.

[DutchHans]

You are right, but why?

[Plantje]

Sorry, I misread the topic title. I searched for "OpenZWave: Received timeout notification from HomeID" and saw it highlighted here (because of the search obviously... duh...) and I thought that was your issue too.