Moderators: leecollings, remb0
@Krizzz i did find this http://tinkerman.cat/sonoff-th10-th16-s ... actuators/krizzz wrote:sincze wrote:krizzz wrote:But probably Hornbach only sells units aproved by TUV after testing. I even have a little bit more faith in this...
This one helped me a lot. I am a newbee and not afraid to try things out. But what doesn't work is the status change in Domoticz when I push the pushbutton. Any idea?sincze wrote:Just the settings for easy_setup.
Sonoff_Settings_3.JPG
Sonoff_Settings_4.JPG
ESPEasy settings for switching a bulb for example.
And at the bottom the settings for the virtual switch in domoticz.
Ow and for the internal LEDCode: Select all
On: http://IP_Address_of_Sonoff/control?cmd=GPIO,12,1 Off: http://IP_Address_of_Sonoff/control?cmd=GPIO,12,0
##UPDATE:Code: Select all
On: http://IP_Address_of_Sonoff/control?cmd=GPIO,13,0 Off http://IP_Address_of_Sonoff/control?cmd=GPIO,13,1
On the ESP Easy Under Tools -> Advanced, I enabled rules. http://www.letscontrolit.com/wiki/index ... rial_Rules
Under rules I entered:
In this way If I call from domoticz:Code: Select all
on lamp_on do gpio,12,1 gpio,13,0 endon on lamp_off do gpio,12,0 gpio,13,1 endon on SW_1#Switch do if [SW_1#Switch]=1 gpio,12,1 gpio,13,0 else gpio,12,0 gpio,13,1 endif endonThis will switch on / off the lamp AND the LED light inside of the Sonoff box.Code: Select all
On: http://IP_Address_of_Sonoff/control?cmd=event,lamp_on Off: http://IP_Address_of_Sonoff/control?cmd=event,lamp_on
In addition pressing the PUSH button on the Sonoff will trigger the light as well and update the domoticz status.
A Slight modification in the device name was needed.
Sonoff_Settings_2.JPG
Nobody with the same issue ;(thecosmicgate wrote:At the moment I am having some send / received = signal problems. Is there someone who moded the antenna to get a bit more / better signal ?
Sent from my SM-G935F using Tapatalk
There are different modules with different antenna's. There are also modules (like the ESP07) that allows to connect an external antenna, so all depends on the module type you have.thecosmicgate wrote:At the moment I am having some send / received = signal problems. Is there someone who moded the antenna to get a bit more / better signal ?
But on the sonoff side there's no difference I think .SweetPants wrote:There are different modules with different antenna's. There are also modules (like the ESP07) that allows to connect an external antenna, so all depends on the module type you have.thecosmicgate wrote:At the moment I am having some send / received = signal problems. Is there someone who moded the antenna to get a bit more / better signal ?
Code: Select all
On: http://esp05/control?cmd=GPIO,12,1
Off: http://esp05/control?cmd=GPIO,12,0Code: Select all
on btn1#Switch do
if [btn1#Switch]=1
gpio,12,1
else
gpio,12,0
endif
endon
on Relay#Switch do
if [Relay#Switch]=1
gpio,13,0
else
gpio,13,1
endif
endon
In Domoticz:how do i add the RSSI wifi strength
.. when i dont add the turnOn rule to control the lamp from domoticz and use the manual on cable switch it works flowlessly, sometimes just minor almost unnoticable delay. but when I add the rule to switch on the lamp to control it via domoticz i get every third time a double click syndrom it means that when i turn the lamp off i see in domoticz log that two commands were sent, first one off and second one On again so my lamp turnes off and on again with just one click. Do you have any idea how to correct that behaviour?Code: Select all
on PhysicalButton#Switch do
if [PhysicalButton#Switch] = 1
gpio,12,1 // close
gpio,13,0 // led on
else
gpio,12,0 // open
gpio,13,1 // led off
endif
endon
on turnOn do
gpio,12,1 // close
gpio,13,0 // led on
endon
on turnOff do
gpio,12,0 // open
gpio,13,1 // led off
endonCode: Select all
#! /bin/sh
/usr/bin/perl /home/pi/domoticz/scripts/$1.pl $2 $3 > /dev/null 2>&1 &
Code: Select all
#!/usr/bin/perl
use JSON::XS;
use LWP::UserAgent;
no warnings 'uninitialized';
# sets a Sonoff device on/off on behalf of Domoticz and then checks that it actually switched accordingly (in case of packet-loss)
($device, $action, $dbg)=@ARGV; # e.g. swGuestroomLamp, on / off
our $debug = ( $dbg == 1 ) || 0; $action=lc($action); $tries=0;
%sonoffs=(
swWardrobeLamp => { ip => '27', idx => '388' },
swAudioengines => { ip => '29', idx => '387' },
swBedroomLamp => { ip => '33', idx => '393' },
swGuestroomLamp => { ip => '34', idx => '394' },
);
$ua=LWP::UserAgent->new; $ua->timeout(1); $ua->env_proxy;
do {
# First send the command to the Sonoff
$url="http://192.168.178.".$sonoffs{$device}{ip}."/control?cmd=event,lamp_$action"; $c=0;
do { $c++;
$response=$ua->get($url);
} until ( ($response->is_success) || ($c==5) );
# Now check if it reacted
$url="http://192.168.178.".$sonoffs{$device}{ip}."/json"; $c=0;
do {
sleep 1; $c++;
$response=$ua->get($url);
} until ( ($response->is_success) || ($c==10) );
if ($response->is_success) {
$devices=$response->decoded_content; $data=decode_json $devices;
foreach $entry (@{$$data{Sensors}}) {
foreach $x (sort keys %{$entry}) { if ($$entry{$x} eq 'relay') { $state=$$entry{state} } };
}};
$ok=( ($action eq 'off') && ($state==0) ) || ( ($action eq 'on') && ($state==1) ); $tries++;
} until ( ($ok) || ($tries==5) );
print "$device: $action --> $state\n" if ($debug);
Users browsing this forum: No registered users and 1 guest