Starting domoticz manually I get the following error: Error: WebServer(HTTP) startup failed on address 0.0.0.0 with port: 8080: bind: Address already in use 2022-10-14 13:57:30.957 Error: WebServer(HTTP) check if no other application is using port: 8080 I tried sudo netstat -tulpn | grep '8080\|433 ...

Hi, This morning I created a HTTP/HTTPS poller, but exidently put in a 0 (zero) as refresh value. Since then domoticz is dead. I removed the domoticz.db file and rebooted the raspberry pi. Domoticz comes back online, so I can upload/restore a database backup. I tried the last 2 hourly and latest ...

I found the problem... the console output is set to serial by default. The "console output" to serial is configured in /boot/cmdline.txt with the entry "console=serial0,115200", which we need to get rid of, but still make sure that there is no "enable_uart=0" in /boot/config.txt. Credits for Maglub ...

Hello all, Since my sd-card (Pi 2B) went corrupt (read-only) I decided to go for a fresh install of Pi OS AND domoticz on a new Pi 4. After some troubles getting a working DB-backup from the broken SD-Card -but manneged to do so- I thought everything was ready to come back online. Unfortunatly I can ...

Finally found the problem... Because the SD card had issue's the current domoticz.db + all backups in Hourly and Daily were corrupt. Luckily the august backup was ok, so I manneged to restore from that one. The corrupt databases could be repaired, but that didn't mean the database-content was ...

A first step might be to perform the steps in this topic database check and repair Howto The database was malformed and the repair did some good... My preferences came back, and so came the scenes, but only about 10 devices (should be at least 300+). If the database turns out to be ok then start ...

Hello, I've been using Domoticz on the same Raspberry pi (2B) since 2015, unfortunately about 3 weeks ago the sd-card got corrupt and went into "read-only" mode. Since then Domoticz and some other services went offline (probably because no logging can't be written). I can acces the data via ssh and ...

Hi, In my room I have dimmable ceiling lights via a Fibaro Dimmer controlled by a monostable wallswitch. In this same room I also have some led-strips controlled via a Fibaro RGBW controller. I would like to make the Fibaro RGBW-controller to mirror the Fibaro Dimmer (on/off and level). If I ...

tontze wrote:Did you try to reset it before adding again ?

Resetting it did the trick. After resetting and including it, 21 new devices showed up

Last week I've added an second Fibaro dimmer type 2 to my zwave network. Inclusion was no problem, but only 3 new devices show up in the devices list. 2 times usage and 1 kwh meter (see attached screenshot). The light itself is not visible as device, so I can't controll the light via Domoticz. I ...

You can use a Fibaro or Qubino Relay.
I guess most people will use the relays to control the lighting, bus you can switch the power of any device (for instance: power outlet, waterpump, ceiling fan, etc.)

Thanks, this did help me a bit. Unfortunately detecting a double pulse coming from a hardware (wired) switch doesn't seem possible. In this example they use a hardware z-wave switch. The switch sends the signal to (in this case) Vera. Then Vera is programmed to translate the press into an action. In ...

I have manual-controlled venetian blinds. To open and close these blinds I want to build a motor into the housing. To control the motor fibaro has 2 components wich can do this: The Fibaro Roller shutter module and the Fibaro relay module. My question: The Roller shutter module is (based on it's ...

For several months I have solar cells and a Toon thermostat. In Domoticz I can view the solar cell data, and I can control the Toon thermostat. I would like to view the solar-data on the Toon thermostat. I know this is possible via 'Zon op Toon', but I don't feel like paying Eneco €100,- to install a ...

Hi, I have two fibaro 2x1.5K relay switch, controlling lighting in hallway upstairs, hallway downstairs and outside. All these lights can be controlled trough domoticz and by three wall switches (pulse). Now I was wondering if it's possible to detect a double-pulse, for instance to turn on the light ...