did you check this page ?
https://www.domoticz.com/wiki/Lost_Username_Password

No that message wasn't given indeed.

After replacing the devices with the new ones (quite a task, have 300+ devices connected) all is running again as expected.
Thanks for the assistance

Enable device receiving on the master server so it is able to get the new devices into your setup.
After that you are able to swap the old devices out with the new ones via the replace option on the device itself.

To follow up on this, it seems the upgrade has triggered new devices to be created in the master server. Once enabled they start to pop up, I'll spend the evening swapping them out against the old devices to see if all is present and if all is updated correctly.

In the 2024.2 update the master system I'm using is failing to get update from slave servers I have 1 primary Domoticz installation and all other are configured as remote servers. Since the update the primary server reports that it fails to update the device. 2024-01-16 08:33:42.445 Error: Pi 14 ...

@kiddigital, yes that was enabled, devices were present but didn't reveive any updates. Also no entries came into the logging.
After recreation it worked fine, I wanted to move the weatherstation at some point in the future but have expidited that now

Thanks for the advice.

Fixed by recreating the OWM Hardware and devices on a different Raspberry Pi, all readings are coming in correctly now. Thanks for the advice, the devices dind't report anything on the old Pi. Statistics are gone off course but that wasn't the main concern. Reused the API key form the old station ...

It isn’t a cache problem. I upgraded 14 Pi’s without a hitch. This one has the sole function of being a virtual weather station and UPS monitor. Only notificaties I get is the mention that the location is found ( Amsterdam, NL). If I put in the exact location based on longitude and lattitude it also ...

Hi, Maybe sombody already has a solution for this, my OWM isn't recieiving any updates on it's sensor since the upgrade to version 2021.1 The worker can be started and stopped without errors, it logs that the worker is started but the sensors aren't updated at all. Did someone else have the same ...

Why don't you disable the automatic adding of new devices on the domoticz settings page ?
When adding a device you can allow it on the same page for 5 minutes to recieve new devices.

Did you enable the system to recieve new sensors ? Did you enable the lacrosse protocol on the RFXCOM ? The manual on the manufacturers website is indeed listing 868 as it is for the 3900 series. ( overlooked that when checking last week) So I can't be sure now ( don't have the 3600 series but the ...

Hi, The WS3600 is transmitting on the 868 MHZ frequency and the RFXcom-XL is using the 433,92 MHZ frequency.
So you won't recieve data unless you have a 868 MHZ reciever.

Thanks Waaren,

That works like a charm.
I just couldn't find the error but you made it very simple to fix.

And yes there was a type in one line indeed.

Hello, Maybe some one here can help me with a ( I hope) simple question but I can't seem to find the solution for it. I have a presence script that is activating the alarm as soon as the mobile phone is out of wifi reach with my local network. commandArray = {} if (devicechanged['Phonename'] == 'Off ...

I created a simple script to test the connection when the pi boots. Explanation of the script: The first command halts the process apcupsd The second command tests the configuration of your apcupsconfig file located at /etc/apcupsd/apcupsd.conf The third command lets the system wait for 5 seconds to ...

The best firmware is depending on which protocols you use. If in doubt, send a message to the RFXCOM support people (b_weijenberg on this forum) so they can give you advice. I needed them once and they helped me within a matter of hours and resolved the issue in a matter of days. Quite happy with ...

I bought the software last week, had some issues with it and contacted support. Nick worked with me over the weekend to get the issue sorted (turned out to be 2 things, rights in domoticz are adjusted after a reboot of the service and too many devices for Google to handle). Today it has been ...

clear your browser cache should fix it