Best wishes for 2024 yet all
I have installed Domoticz 2024.1, but now it does not find the Aeotec Z-Wave Plus Z-Stick Gen5. In the hardware can't find "OpenZWave USB" ?
Now I cannot install the Aeotec Gen 5 anymore. How can this problem be solved?

Hello, Thank you for the information. But I have no programming skills. Is there anyone who has an example how to adapt the sketch for a temperature sensor from Domoticz instead of: " // Temperature sensor pin const int ROOM_TEMP_SENSOR_PIN = 14; //for Arduino, 14 for ESP8266 (D5), 18 for ESP32 ...

Hello, I am experimenting with an OpenTherm board from Diyless ( https://diyless.com/blog/domoticz-opentherm-thermostat) This board is connected to an ESP8266. The diyless OpenTherm board has a temperature sensor on it. I ran into the following problem, maybe someone has a solution for the following ...

Hello all, After the Domoticz stable update, almost everything works. However, I can't get 1 device to work anymore. It is a Fibaro FGRM222 Roller Shutter. If I go to the Node management and then control panel. Then I can open and close the roller shutter. In Domoticz the device shows the status ...

Hi,

Thanks a lot for the script. It works now.

Hi, I currently have a device of the type "General, kWh". This device gives me two values. The first is the current solar energy and the second is the value of today's total solar energy in kWh. I would like a separate device that only displays the kWh generated by the solar panels today. The device ...

Hello,

I have a device called "Electric (Instant+Counter)". I want to create a new device that only shows the counter value. Can someone give me an example of how to do this in dzVents?

Thank you very much

Hi, @gimic

I could not evaluate Home Connect any more.
The biggest problem I ran into in the end was that the Home connect server always threw me out after a few days. This was because there were too many requests.
When this is solved I will continue with the Home connect thing.

Robin

Hi thanks for the answer.

When I install the plugin, and choose the plugin in "hardware". Which port should be filled in at "port" ?
And I see no devices?

Hi MarioPeters,

Great that you will post the wiki, I didn't not know what to fill in, what "port" and when I install the plugin there are no Devices

Hi,

I agree with that, thanks

Regards

Hi thanks for the response, The first picture represents the "Home Connect" nodes from https://flows.nodered.org/node/node-red ... omeconnect. Correct? Yes, the first picture represents the "Home Connect" node from https://flows.nodered.org/node/node-red ... omeconnect. Which version of Node Red do ...

Hi, After a while I decided to use Node Red to connect with the Bosch Dishwasher. I can now start/stop the dishwasher and can choose between differs programs with Node Red. But now I have problems to connect a virtual switch in Domoticz that connect with MQTT to Node Red and start a program. I have ...

Thanks for the info, It woud be great if there was a working plugin for Domoticz to communicate with Home-Connect. That's the way you can build your own smart home with appliances that you can start when the sun shines. There is a Home-Connect plugin from Mario Peters on this forum, but it seems ...

Hi, is it possible to start and stop my dishwasher with "home-connect" with Domoticz ?

Thanks

Thanks for the information, then the best way is "timer=every minute"

Hi, I tried this script with an older script that you have written, but it isn't working. I probably did something that is not right. local scriptVar = 'myCustomTimer' return { on = { timer = { 'every minute', }, customEvents = { scriptVar .. '*', -- event triggered by emitEvent }, }, logging ...

Hi,

Is it possible to let run a script not every minute but every 30 seconds?

on = { timer = { 'every minute'},

Thanks

Hi, Doesn't Domoticz have a UDP listerner plugin that can do this? Then it is probably possible to communicate directly with the Batrium from Domticz. If the values can be retrieved using a JSON via HTTP Get then dzVents can collect it and update virtual sensors with the information. I don't know if ...

Hi FireWizard, Thanks for the response I'm not familiar with the MQQT. But if I'm right, WatchMon UDP Binary Listener translates to JSON and stores to influxdb or sends it to MQTT . So I need a separate server, e.g. Rasp Pi, which I connect to the wifi from Batrium BMS on which WatchMon UDP Binary ...