with some browsers it is also sufficient to press the Shift key and F5 (reload). Then the switches are displayed.

This forum has helped me countless times.
I hope this post will help someone as well.

I'm always looking for something new, especially now in lockdown time. For another project I needed a permanent weight monitor (not for the pounds I gain during Corona :-D ).
I didn't want to set up an extra ...

Seperate <ip>,<port>,<url> with comma's

this is so diabolical

I figured out that the SendToHTTP command is not necessary.
the value is already sent to the stored controller via HTTP. in the dummy sensor the IDX is specified.

I have removed the line and it runs quite well so far.

I am such a dork :lol: :lol: :lol:
thank you very much for the help.
After the change and a reboot the correct values are displayed in the log and the variables are filled correctly.
However, I now have a very strange error message and nothing is transferred to domoticz:

water3.png

the rules ...

hello,

this thread is really very good and has helped me a lot with my project.
i used a proximity sensor LJ18A3-4-Z-BX instead of the infrared sensor TCRT5000. This works very well.

@sincze: thanks a lot for the waterflow script. that works decent too. but i have a question about that and maybe ...

I WANT THIS

Hello @FireWizard,

You are absolutely amazing!
IT WORKS
I had seen the point at mqtt in node and corrected it, but it didn't occur to me to do the same in the function node. that's not where I noticed it.
I am so happy that it is finally working now!!! Many many thanks for that.
verbrauch.png ...

Hello FireWizard,

thank you for your answer and the detailed explanations.
The two inputs and the join is completely ingenious.

I have tested your flow and unfortunately have to say that at the end comes out again undefined :-(

As you can see in the screenshot below after the join at debug node ...

Hello FireWizard,

first of all thank you for your prompt reply.

to your questions:
the orginal topic in volkszähler is vzlogger/data, that's right. I had changed it to domoticz/in since I don't have any other mqtt stuff and thought it has no effect.

the node red nodes for volkszähler i didn't ...

Hi @FireWizard,
you are my last great hope :-)
I sit now for days on it and just do not come further.
I always get only: svalue: undefined out. Somewhere I have an error, but I just can't find it. Maybe I am doing fundamentally wrong.
I have the hope that you with your knowledge simply say "Yes ...

Hello,

this is a very interesting approach.
But i don't know how to get the data into domoticz (the last step) do you know further steps?

best regards

Hello,

is there anyone here who has managed to read ISKRA's smart electricity meter MT681 and display it in Domoticz?
I despair meanwhile. I think I have read 3/4 of the entire internet.
The meter has an optical interface (9600bd, 8N1) which sends a SML message every second.
This interface is read ...

Hello,

i also have this Sensor.
where did you get the receiver rtl_433 RTL-SDR receiver?
is there any information or documentation about it?

would like to integrate the sensor into my system as well.

best regards Marco

I also use the room plan. so you caqn group anything you want.
you find room plans here; Configuration-->More Options-->Plans--> room plan

best regards

Hello,
i'm using the following system:
RPi 1 with EnOcean USB 300 USB-Gateway 868MHz / TCM310 Chipset
System is: V3.8796

First of all, it'S a great software. i'm happy to find Domoticz.

here is my problem, i hope someone knows a solution or an answer:

i had allready teach-in some switches an ...

Hello,

i have the same problem with my blinds.
i also need the feature of a "long" press.

Is there anyone who know the right way or a workaround?

thanks a lot
best regards

marco