I am only controlling dummy switches with timers. I see in the protocol of the switch, that the timer didn‘t work, because the switch did not change. The problem is, that they sometimes work and sometimes not.
I am using a pi 4.

There are a lot of mqtt messages for my shelly plugs. Temperature, power, voltage. The devices were autmatically createt. Now I deletet this devices which I don't need and deactivatet accept new devices. So I only get messages that there are mqtt messages but accept new hardware is disabled. I hope ...

Yes, 1:35 after sunrise

yesterday I deactivated the time script. Now the timers run. But there's one thing. I have a timer on a switch with 1:35 after sunrise. Sunrise was in domoticz declared for 6:03. The switch was triggered on 7:52. Normaly this should have happened on 7:38. Perhaps theres the problem?

with top I see, that the cpu is not the problem. The mqtt auto discovery topic is homeassistant. For the shellies I used shellyteacher4domo to use autodiscovery. In my opinnion there's a problem with queuing the time script and the timers because I see nothing in the protocol of the switch and in ...

I have always more than 2 minutes. I see, that some timers don't work (in protocol of the switch). Sometimes they work. As I use timers for some automations this is not good. When I change them or delete them and make new, they sometimes run. I think, there maybe a general problem with timers. Is ...

So I included a print at start and one at the end of the time script, This are only some seconds between. But in some subroutines called by the time script I handle some url's and json outputs. I see in the protocol of the switches, that the timer wasn't startet. May there is a problem, when the ...

I think, the problem is, that a device timer does not start, when a time script is running. Is this correct?

Hello, I use timers on switches and on setpoint devices. I use after sunset, before sundown and exact timers. I often have the problem (2025.1) that timers don't work. I see it in the protocol of the device. Then I change the timers and perhaps they work again. I also use a time lua script, which ...

I don't know, but I prefer to use the basic protocol and this is matter for tadoX. My only question was, if it could be possible to integrate the home assistant matter solution in domoticz? Somebody did this also some times ago for the mqtt auto-explore I think. Another advantage of matter is, that ...

At the moment I have 2 tadoX thermostats, I will use more of them in the future. I use home assistant as a bridge to domoticz (with scripting vice versa), I'd also like to buy the new Eltako 64 dimmers with matter. It would be easier to have it in domoticz without home assistant.

Are there any news about matter integration? As I wrote before, wouldn't it be possible to add the home assistant matter integration t domoticz?

At the moment I have HA as a virtuel machine on my Synology. 2 tado thermostats are integrated. I interface with domoticz via HA automations and lua scripts. So HA is acting in my system as a matter bridge. Wouldn't it be possible, to integrate the HA-matter solution to domoticz like it was done ...

For using a matter thermostat, I installed home assistant on my second pi. I searched the internet but I don't find, how to interface the values of the real home assistant thermostat to my domoticz dummy thermostat (state, temperature, wanted temperature and humidity). I found, that mqtt is the ...

Now I bought a todo x thermostat with matter. I integrated it into the tado-app and into homekit. I did a homekit automation, that thermostat goes off, when the corresponding window is open (dummy-switch in domoticz with homebridge in homekit) and reverse. But homekit automations are not very ...

I'm using domoticz since 9 years and still like it very much. I startet with my somfy-rfx blinds and now I use shellys, z-Wave, rfxcom, dummy-devices in combination with homebridge, homebridge-edomatic to handly via siri from my ios-Devices. Event handling in combination with lua is my most used ...

To see your version and the available updates use :

sudo snap info zwave-js-ui

To do the update to the latest stable version use :

sudo snap refresh zwave-js-ui

I asked chatgpt to program a inteface to control tado x (matter based) thermostats from domoticz via matter.js. The question was? "program a interface to control matter based tado x thermostats via matter.js from domoticz vice versa" The result was a phyton interface plugin. I don't know, if this ...

On github I found a project matter.js (https://github.com/project-chip/matter.js) which seems to be something for developping matter-bridges to existing smarthome-systems. Onother thing I found is matterbridge (https://github.com/Luligu/matterbridge) Could this be something for domoticz? When apple ...

I'd like to change my Z-Wave thermostats to the new tado-X. Normally I have a lot of my domoticz content in homekit via homebridge and homebride-edomatics plugin. tado-X can handle matter, so the integration to homekit via my homepod mini as a matter router should not be the problem. But what's ...